PepeTools Ultra Power Electric Wire Rolling Mill 130mm, MADE IN THE USA

Description

PepeTools Ultra Power Electric Rolling Mills
Proudly Made in the USA
Ultra Power Electric Rolling Mills
designed for cold rolling of nonferrous metals to produce uniform thickness and bright finish.
You will be able to reduce thickness (gauges) of sheet metal and form square, round, comfortable fit and elliptical (1/2Rd) wire
.
Transfer textures to your metal, and many other related tasks.
The "T" bar
at the top of the Rolling Mill used to open or close the rollers. When completely closed the rollers, should measure "true" cylindrically. This means they should touch with no visible gaps. Should there ever be a gap, meaning the rollers are not "true", simply remove the two small screws holding the "T" bar cover , pull the "T" bar handle off and turn the large gears to move the roller(s) down until there is no visible gap, making them "true", then re-install the "T" bar and cover.
To roll metal:
·
Open the rollers to accept the metal and close the rollers around the metal using the "T" bar until the rollers touch and hold the metal.
·
Set the indicator dials on the large gears to "0" (zero), Indicator Dials are on the top of each Rolling Mill.
·
Turn on the Power Mill and Select Forward. Select Speed at which the Roller moves with the Center Dial (0-100).
·
Tests pass the metal through.
·
Once the test pass been completed, you will want to turn the "T" bar clockwise one quarter of the space between the markings on top of the gears, any greater distance could damage the mill.
·
Continue to pass the metal through the rollers until the desired thickness is achieved.
Care for your investment.
Lightly oil, using a small cloth towel and oil, then drape the cloth over the rollers to protect them from rust when not in use. Keep the mill clean and occasionally apply a light coating of oil to the entire frame. Always keep your roller surfaces clean and free from dust and debris.
Safety Notice:
*Install Feeding table(s) with Roller guards - before operating the rolling mill. Mounting hardware and wrench is included in the package.
Country/Region of Manufacture: United States
PepeTools Ultra Power Electric Rolling Mills
Mechanical Features:
Rollers: 130mm Length x 65mm Diameter - “Mirror” finished and induction hardened to 60-62 HRC
Wire Rollers:  Graduated Eight sizes of Square Wire 1.0 mm, to 4.5mm;  Five Sizes of Round 2mm to 6mm, Five Sizes of Comfortable Fit from 4.0 mm to 8.00 mm Wide and Three Elliptical (half-round)  from 2.5mm to 4.0mm Wide
ULTRA Rolling Mill Body is one-piece construction - precision cast from Ultra Strong
Ductile Iron
for added strength and durability.
Industrial Grade - Heavy Duty Worm Gearbox* - Rated 12,000 Hours Continues Duty
Nominal torque output 2200 Inch-Lb
Production Output - 9.5 Ft/min or 2.9 m/min
Variable Speed 0-12 RPM
Control Features:
A Digital Hybrid AC Drive with Analog Interface - Vented NEMA 1 / IP 20 Enclosures
On/Off AC Line Switch
Forward-Stop-Reverse Switch
Variable Speed 0-100
Excellent speed regulation with high torque loads throughout the entire speed range.
200% - Starting Torque
Holding Torque at Zero Speed in "Stop" mode
Flux Vector Compensation with Static Auto-Tune
Ride-Through momentary power loss
Regeneration Protection eliminates tripping
Safety Features:
Feeding and Receiving tables with Roller guards*
Overload protection
Under voltage / Overvoltage Protection
Short Circuit Protection, phase to phase
Electronic Inrush Current Limit (EICLTM) Protection
Run/Fault Relay Output Contacts
Product ordering and dimensional information:
Single Mill
120V:
189.30. 120V -130mm Fancy Wire
Dimension – Footprint:
L18” x W10” x H17” (457mm x 254mm x 431mm) – Weigh 96lb 43kg
Shipping Dimension:   L24” x W20” x H24” (610mm x 510mm x 610mm) – Weigh 109lb 49kg
Safety Notice:
*
Install Feeding table(s) with Roller guards - before operating the rolling mill. Mounting hardware and wrench is included in the package
.
Track Page Views With
Auctiva's FREE Counter